primary drying raises a handful of sensible questions. This page answers them in order, starting with the fundamentals and moving to applications.
This page was last updated on 2025-05-22 and is reviewed periodically as new material appears.
Freezing is the first stage and sets the ice structure that later becomes the pore network. The formulation is cooled below its freezing point, often with a controlled ramp, and solutes concentrate as ice forms. Primary drying then lowers chamber pressure and supplies heat to sublime the ice. The product temperature must stay below its collapse or eutectic temperature to prevent structural loss. Secondary drying raises the temperature modestly to remove bound water and achieve a low residual moisture.
A freeze-dryer consists of a vacuum chamber, temperature-controlled shelves, a condenser, and a vacuum pump. Vials, ampoules, or bulk trays hold the product during the cycle. The condenser traps water vapor as ice at a temperature lower than the product. Cycle development balances shelf temperature, chamber pressure, and time. Scale-up can be difficult because heat and mass transfer change with equipment size, so process analytical tools and conservative validation are often used.
Lyophilization is a dehydration technique in which a product is frozen and the solvent is removed under reduced pressure. The low pressure allows ice to sublimate directly into vapor without passing through a bulk liquid phase. This differs from conventional drying, where heat drives evaporation and can damage heat-sensitive structures. The process is used for biological materials, pharmaceutical formulations, and some foods. Its main advantage is preservation of porous structure and rapid reconstitution.
In practice, lyophilization is slower and more energy intensive than simple drying. Cycle times can range from hours to several days depending on load, container, and formulation. Amorphous materials may require excipients that help preserve structure during freezing and drying. The method is widely used for biological materials, pharmaceuticals, and foods where heat drying would cause unacceptable change. Open questions remain about scaling cycles between laboratory and production equipment, and this gap affects technology transfer.
Lyophilization removes water by freezing a material and then lowering pressure so ice changes directly to vapor. The process relies on sublimation, the phase transition from solid to gas without an intermediate liquid state. Because the material remains frozen during primary drying, the structure often stays porous. This porous matrix can rehydrate quickly when water is added back. The low pressure also allows vapor to leave the solid matrix without boiling.
| Property | Value | Notes |
|---|---|---|
| Common synonyms | freeze-drying, lyophilisation, cryodesiccation | Lyophilization is common in pharmaceutical literature. |
| Typical chamber pressure during primary drying | 0.05–0.5 mbar (5–50 Pa) | Must remain below the triple point of water. |
| Typical shelf temperature during freezing | −40 to −20 °C | Lower temperatures may be used for eutectic systems. |
| Typical residual moisture after secondary drying | 0.5–3% w/w | Product-dependent; low moisture improves stability but can cause over-drying. |
| Typical analytical method for residual moisture | Karl Fischer titration or loss on drying | Thermogravimetric methods are also used. |
Formulation composition influences whether freeze-drying produces an intact cake or a collapsed mass. Excipients such as sugars and polymers can raise the collapse temperature and provide bulk during drying. The critical temperature for primary drying is often the collapse temperature or the glass transition temperature of the maximally concentrated phase. If the product temperature exceeds this threshold, the frozen matrix may soften and lose structure. Established practice therefore links shelf temperature and chamber pressure to the formulation's thermal properties.
The physics of freeze-drying couples heat transfer, mass transfer, and phase change. Heat supplied through the shelf must reach the sublimation front without melting the ice or degrading the product. Water vapor then travels through the already dried layer and leaves the chamber, where low pressure and cold traps keep it from returning. The dried layer acts as a resistance to vapor flow, so drying rate changes as the front recedes. Open questions remain about how pore structure and formulation heterogeneity affect drying uniformity at larger scales.
Lyophilization removes water from a frozen material by sublimation under reduced pressure. The process begins with freezing, which converts liquid water into ice and fixes the structure of the sample. After freezing, primary drying lowers pressure so ice changes directly to vapor without passing through a liquid phase. Secondary drying then removes bound water that remains after ice sublimation. The result is a dry, porous solid that often retains its original shape.
The low pressure used during drying allows water vapor to move from the ice surface to a cold condenser. Energy supplied as heat drives sublimation but must stay below the collapse temperature of the frozen matrix. If the product becomes too warm, the frozen structure may soften or melt, reducing pore formation and slowing drying. Formulations often include bulking agents, stabilizers, or buffers to support a rigid cake. The final moisture content depends on formulation, freezing rate, and the length of secondary drying.
A typical cycle begins with freezing, sometimes including an annealing step to control ice crystal size. Freezing conditions influence the pore network that later allows vapor escape. During primary drying, shelf temperature and chamber pressure are set so heat enters the product while its temperature stays below the collapse or eutectic point. Secondary drying then raises the shelf temperature to desorb bound water and lower residual moisture. Cycle design depends on formulation, fill volume, container type, and equipment capability.
The physics of lyophilization couples heat transfer, mass transfer, and phase behavior. Sublimation requires a vapor pressure difference between the ice front and the chamber, and the dried layer adds resistance to vapor flow. Amorphous formulations are characterized by a glass transition temperature of the maximally freeze-concentrated solute, often denoted Tg'. Crystalline bulking agents can provide structure, while amorphous excipients stabilize labile components. Open questions remain about spatial heterogeneity, edge effects, and how laboratory cycles scale to production.
Lyophilization is a drying process in which a solvent, usually water, is removed from a frozen material by sublimation under reduced pressure. The material is first solidified, then placed under vacuum so that ice transitions directly to vapor without a bulk liquid phase. This approach suits heat-sensitive substances that would degrade during conventional evaporation. Primary drying removes unbound ice, while secondary drying reduces water that remains adsorbed to the solid matrix. The result is a porous, lightweight solid that can be reconstituted later.
Lyophilization is a dehydration process that removes water from a frozen material by sublimation under low pressure. The material is first frozen to convert liquid water into ice. Next, the pressure is reduced below the triple point of water so that ice changes directly into vapor without passing through a liquid phase. This step is called primary drying. The result is a porous solid or cake that retains the original shape of the frozen solution.
After primary drying, secondary drying removes water that remains bound to the material. This stage raises the shelf temperature while maintaining low pressure, which encourages desorption of unfrozen water. Residual moisture can be reduced to a low percentage, improving stability for many products. The process parameters, including freezing rate, shelf temperature, and chamber pressure, influence the final pore structure and reconstitution behavior. Control of these variables helps prevent collapse or meltback during drying.
A formulation often contains excipients that protect the active ingredient during freezing and drying. Bulking agents provide structure, while lyoprotectants stabilize sensitive molecules. The freezing step can produce ice crystals whose size and distribution affect the drying rate, and cycle design includes freezing, annealing, and drying phases. If the product temperature rises above a critical value, the cake may collapse or lose its porous structure. Successful lyophilization therefore depends on the interaction between formulation, equipment, and cycle design.
Amyloid beta can be measured semiquantitatively with immunostaining, which also allows one to determine location. Amyloid beta may be primarily vascular, as in cerebral amyloid angiopathy, or in amyloid plaques in white matter. One sensitive method is ELISA which is an immunosorbent assay which utilizes a pair of antibodies that recognize amyloid beta. Atomic force microscopy, which can visualize nanoscale molecular surfaces, can be used to determine the aggregation state of amyloid beta in vitro. Vibrational microspectroscopy is a label-free method that measures the vibration of molecules in tissue samples. Amyloid proteins like Aβ can be detected with this technique because of their high content of β-sheet structures. Dual polarisation interferometry is an optical technique which can measure early stages of aggregation by measuring the molecular size and densities as the fibrils elongate. These aggregate processes can also be studied on lipid bilayer constructs. TPM21 Sylvain Lesné – Aβ*56 Online Mendelian Inheritance in Man (OMIM): 104300
Recent discoveries made through use of high-throughput 'omics approaches include the fact that AAV capsids are post-translationally modified (PTM) during production such as acetylation, methylation, phosphorylation, deamidation, O-GlycNAcylation and SUMOylation throughout capsid proteins VP1, VP2 and VP3. These PTMs differ depending on the manufacturing production platform. Another such discovery is the fact that AAV genomes are epigenetically methylated during production. Besides price, these findings might affect expression kinetics, rAAV receptor binding, trafficking, vector immunogenicity, and expression durability.
Division of analytical chemistry and laboratory of bio-electrochemical biosensor research function in this department. The division conducts research in the area of methods of electrochemical analysis using chemically modified electrodes and biosensors. The head of the department is Professor Gennady A. Evtyugin, doctor of Science in chemistry. The Department conducts research in the following fields:
Annex 13 of the Chicago Convention provides the international Standards And Recommended Practices that form the basis for air accident and incident investigations by signatory countries, as well as reporting and preventive measures. The International Civil Aviation Organization (ICAO) is specifically focused on preventing accidents, rather than determining liability. In Australia, the Australian Transport Safety Bureau is the federal government body responsible for investigating transport-related accidents and incidents, covering air, sea, and rail travel. Formerly an agency of the Department of Infrastructure, Transport, Regional Development and Local Government, in 2010, in the interests of keeping its independence it became a stand-alone agency.
Anti-obesity medication or weight loss medications are pharmacological agents that reduce excess body fat and cause weight loss. These medications alter one of the fundamental processes of weight regulation, by: reducing appetite and consequently energy intake, increasing energy expenditure, redirecting nutrients from adipose to lean tissue, or interfering with the absorption of calories. Weight loss drugs have been developed since the early twentieth century, and many have been banned or withdrawn from the market due to adverse effects, including deaths; other drugs proved ineffective. Although many earlier drugs were stimulants such as amphetamines, in the early 2020s, GLP-1 receptor agonists became popular for weight loss. As of 2023, the medications liraglutide, naltrexone/bupropion, orlistat, semaglutide, tirzepatide and phentermine/topiramate are approved by the US Food and Drug Administration (FDA) for weight management in combination with reduced-calorie diet and increased physical activity. Medications to treat obesity may be considered in those with a body mass index above 30, or above 27 with obesity related complications (such as hypertension, hyperlipidemia, cardiovascular disease, or obstructive sleep apnea). As of 2022, no medication has been shown to be as effective at long-term weight reduction as bariatric surgery.
Sources: en.wikipedia.org
Blood sugar regulation is the process by which the level of blood sugar, the common name for glucose dissolved in blood plasma, is maintained by the body within a narrow range. This tight regulation is referred to as glucose homeostasis. Insulin, which lowers blood sugar, and glucagon, which raises it, are the most well known of the hormones involved, but more recent discoveries of other glucoregulatory hormones have expanded understanding of this process. The pancreas gland secretes two hormones that are primarily responsible for regulation of glucose levels in blood. Blood sugar levels are regulated by negative feedback in order to keep the body in balance. The levels of glucose in the blood are monitored by many tissues, but the cells in the pancreatic islets are among the most well understood and important. Granule docking is an important glucose-dependent step in human insulin secretion that does not work properly in type 2 diabetes.
isoform.io is a database of AlphaFold2-generated structures of proposed splice isoforms in the human genome. It includes information from 237,275 human transcripts. It has been used to detect errors in the mRNA predictions for a handful of genes. AlphaFold has shown certain limitations. AlphaFold DB provides models of individual protein chains (monomers), rather than their biologically relevant complexes. Many protein regions are predicted with low confidence score, including the intrinsically disordered protein regions. Alphafold-2 was validated for predicting effects of point mutations on structure and free energy, with a partial success.
In physics and chemistry, binding energy is the smallest amount of energy required to remove a particle from a system of particles or to disassemble a system of particles into individual parts. In the former meaning the term is predominantly used in condensed matter physics, atomic physics, and chemistry, whereas in nuclear physics the term separation energy is used. A bound system is typically at a lower energy level than its unbound constituents. According to relativity theory, a ΔE decrease in the total energy of a system is accompanied by a decrease Δm in the total mass, where Δmc2 = ΔE. There are several types of binding energy, each operating over a different distance and energy scale. The smaller the size of a bound system, the higher its associated binding energy.
Alfred Stracher (1931-2013) was an American biochemist and the founder and editor-in-chief of Drug Delivery. During his lifetime, he was Distinguished Professor of Biochemistry at SUNY Downstate Medical Center. Alfred Stracher was born in Albany, New York in 1931. He graduated from Rensselaer Polytechnic Institute in 1952 with a Bachelor of Science in Chemistry. He received his PhD in Chemistry from Columbia University in 1956.
Sources: en.wikipedia.org
Yes, the terms are generally interchangeable. Lyophilization is more common in pharmaceutical and laboratory contexts, while freeze-drying appears widely in food science and general writing. Both describe removal of solvent by sublimation under vacuum after freezing.
Reduced pressure keeps the process below the triple point of water, so ice can sublimate directly to vapor. It also lowers the temperature needed for drying, which helps preserve heat-sensitive materials. Without vacuum, melting or boiling could occur instead of controlled sublimation.
The rate depends on heat transfer to the product and mass transfer of vapor through the dried layer. A cold condenser, adequate vacuum, and suitable shelf temperature all influence speed. Formulation properties such as solid content and collapse temperature also set practical limits.
Primary drying removes ice by sublimation under vacuum. Secondary drying removes water that is bound to the material, often by warming the product after most ice has left. Both stages occur below temperatures that would cause unwanted melting.