A practical reference on Water content: what it is, how it behaves, what the literature reports, and where the honest uncertainties sit.
Reviewed 2026-02-05. Anything still debated is marked as such rather than presented as settled.
Storage stability depends on water content, oxygen exposure, and temperature. Lyophilized solids are hygroscopic and can absorb water if exposed to humid air. Vials are usually sealed under vacuum or inert gas with rubber stoppers and aluminum crimps. Storage temperatures range from room temperature to refrigerated or frozen conditions depending on the material. Stability studies track potency, moisture, and physical form over time. Accelerated conditions can reveal sensitivity but may not predict long-term behavior.
Analytical methods for lyophilized materials include X-ray diffraction for crystallinity, differential scanning calorimetry for thermal transitions, and scanning electron microscopy for pore morphology. Moisture sorption analysis shows how the cake responds to humidity. These methods help distinguish amorphous from crystalline states and detect phase changes. Open questions remain about how pore structure changes during long-term storage and how best to predict collapse under varied conditions. Comparisons across studies are complicated by differences in formulation, cycle, and storage history.
Quality control for lyophilized products focuses on appearance, moisture level, reconstitution time, and structural integrity. A cake should be uniform, intact, and free of meltback or collapse. Moisture level is measured by Karl Fischer titration or thermogravimetric analysis. Reconstitution time reflects pore structure and formulation. Visual inspection and vial integrity checks detect cracks, stopper defects, or particulate matter. These checks are often performed on samples from each batch. They help confirm that the drying cycle performed as intended.
Analytical methods for lyophilized solids must account for the low moisture content and the fragile cake. Karl Fischer titration is widely used for water content, while near-infrared spectroscopy can measure moisture non-destructively in sealed containers. X-ray diffraction and modulated differential scanning calorimetry help identify crystalline or amorphous phases. Residual solvent analysis may be needed if organic solvents were used during formulation. The combination of these methods supports batch release and long-term stability assessment.
Lyophilized products are typically stored as sealed solids in vials or syringes. Moisture ingress is a major concern because many dried cakes are hygroscopic and can lose stability when exposed to humid air. Storage temperature depends on the formulation; some products are kept refrigerated, while others are stable at room temperature. Container closure integrity and headspace moisture are often monitored. Light protection may also be required for some photosensitive materials.
| Property | Value | Notes |
|---|---|---|
| Appearance | White to off-white porous cake | Color and texture vary with formulation. |
| Reconstitution time | Seconds to several minutes | Depends on cake porosity, excipients, and diluent. |
| Typical moisture level | 0.5-3% w/w | Lower values suit hydrolysis-sensitive materials. |
| Common moisture method | Karl Fischer titration | Coulometric mode is common for low water levels. |
| Typical storage temperature | 2-8 °C or ambient | Some products require frozen storage; protect from humidity. |
Stability programs monitor lyophilized products under defined temperature and humidity conditions over time. Real-time studies at recommended storage conditions are the reference, while accelerated studies provide early signals of degradation pathways. Because a dry cake can still undergo oxidation, hydrolysis, or aggregation, stability depends on residual moisture, excipients, and container headspace. Open questions include how best to predict long-term stability from short accelerated runs and how vial-to-vial variability affects shelf life. Current guidance treats these predictions as product-specific rather than universally generalizable.
Freeze-dried materials are hygroscopic to varying degrees and can take up moisture after drying. Storage therefore often uses sealed glass vials, rubber stoppers, and crimp seals to limit contact with ambient humidity. A desiccant may be included for moisture-sensitive products, although it is not universal. Controlled room temperature is sufficient for many lyophilizates, while others require refrigeration or freezing. Moisture ingress remains a primary cause of cake collapse, chemical degradation, and loss of reconstitution performance.
Handling practices aim to prevent moisture ingress and mechanical damage. Vials should remain stoppered and crimped until use, and reconstitution should follow the labeled diluent and volume. Shipping may involve temperature-controlled containers and desiccants, but direct contact between desiccant and product is avoided. Regulatory guidance expects documented storage conditions, excursion assessments, and stability commitments. Open questions remain about how best to predict long-term stability from short accelerated studies for every formulation class.
After lyophilization, the product is usually a porous cake or powder with a large internal surface area. This structure can absorb moisture quickly if exposed to humid air, so vials are sealed under vacuum or an inert gas. Moisture uptake may lower the glass transition temperature of the dried matrix and accelerate chemical or physical degradation. Storage conditions therefore depend on the formulation, container, and intended shelf life. Some products remain stable at room temperature, while others require refrigeration or freezing.
Quality control for lyophilized products includes appearance, cake structure, reconstitution time, pH, residual moisture, and potency. Residual moisture is a key attribute because excess water can reduce stability, while excessively low moisture may cause structural changes or aggregation in some systems. Stability studies compare real-time and accelerated conditions to estimate shelf life. Analytical methods must be validated for the specific matrix, container, and moisture range. Sterility and container integrity are also monitored for sterile products.
Quality control for freeze-dried forms includes visual inspection, water content measurement, and reconstitution time. A satisfactory cake is typically uniform, porous, and intact, although minor shrinkage or cracking may be acceptable if specifications allow. Karl Fischer titration, thermal gravimetric analysis, and near-infrared spectroscopy are used to measure water content. Reconstitution is assessed by adding a specified diluent and recording the time and ease of dissolution. Microbiological and particulate tests are added when the product is sterile or intended for injection.
Stability of a lyophilized solid depends on water content, temperature, and the physical state of the formulation. Amorphous products may slowly absorb moisture and drop below their glass transition temperature, causing collapse or crystallization. Some proteins and peptides can aggregate even in a dry state, especially when exposed to heat or moisture. Accelerated stability studies at elevated temperature and humidity help estimate shelf life, but real-time data remain the basis for expiration dating.
After drying, a lyophilized product is usually sealed under vacuum or an inert gas to limit moisture and oxygen exposure. The container closure system matters because stoppers and seals can allow moisture ingress over time. Storage conditions are selected from stability studies that track potency, cake appearance, and reconstitution behavior. Many freeze-dried materials are kept at controlled room temperature, while some require refrigeration or protection from light.
Quality control for freeze-dried lots combines visual inspection with instrumental tests. Cake appearance, color, and shrinkage are recorded against a reference, while residual moisture is measured by Karl Fischer titration or loss on drying. Thermal analysis can reveal phase transitions and crystallization events, and X-ray diffraction distinguishes amorphous from crystalline solids. Microbiological tests and container closure integrity checks are also routine for sterile products. Analytical methods must be validated for the matrix, because excipients and low moisture can affect accuracy. Open questions include how best to predict long-term stability from short-term data.
Lyophilized solids are often hygroscopic, so handling occurs in controlled low-humidity areas or glove boxes when the material is exposed. Vials remain sealed with elastomeric stoppers and aluminum crimps until use, because airborne moisture can raise residual water and shorten shelf life. The porous cake is fragile and may crack, shrink, or powder during transport. Personnel typically avoid repeated warming and cooling of sealed units, which can draw moisture through closures. These practices aim to preserve the low water content achieved during drying.
As mentioned above, G-proteins may terminate their own activation due to their intrinsic GTP→GDP hydrolysis capability. However, this reaction proceeds at a slow rate (≈0.02 times/sec) and, thus, it would take around 50 seconds for any single G-protein to deactivate if other factors did not come into play. Indeed, there are around 30 isoforms of RGS proteins that, when bound to Gα through their GAP domain, accelerate the hydrolysis rate to ≈30 times/sec. This 1500-fold increase in rate allows for the cell to respond to external signals with high speed, as well as spatial resolution due to limited amount of second messenger that can be generated and limited distance a G-protein can diffuse in 0.03 seconds. For the most part, the RGS proteins are promiscuous in their ability to deactivate G-proteins, while which RGS is involved in a given signaling pathway seems more determined by the tissue and GPCR involved than anything else. In addition, RGS proteins have the additional function of increasing the rate of GTP-GDP exchange at GPCRs, (i.e., as a sort of co-GEF) further contributing to the time resolution of GPCR signaling. In addition, the GPCR may be desensitized itself. This can occur as:
Genetically modified organism History of biotechnology An Asilomar Moment Archived 10 July 2013 at the Wayback Machine Original Asilomar Genetics Guidelines “Asilomar Conference.” Provides another summary of the Asilomar Conference. The Basics of Recombinant DNA provides an introduction to the science behind recombinant DNA. The Recombinant DNA Debate Archived 31 March 2007 at the Wayback Machine provides more details about the history of the debate surrounding the use of recombinant DNA technology. “Paul Berg: The 1980 Nobel Prize in Chemistry – Autobiography.” Provides an autobiography about Paul Berg. Science History Institute: The story of the 1975 Asilomar Conference on Recombinant DNA
The full-length human protein comprises 2,843 amino acids with a (predicted) molecular mass of 311646 Da. Several N-terminal domains have been structurally elucidated in unique atomistic high-resolution complex structures. Most of the protein is predicted to be intrinsically disordered. It is not known if this large predicted unstructured region from amino acid 800 to 2843 persists in vivo or would form stabilised complexes – possibly with yet unidentified interacting proteins. Recently, it has been experimentally confirmed that the mutation cluster region around the center of APC is intrinsically disordered in vitro.
An antibody–drug conjugate consists of three components: Antibody - targets the cancer cell surface and may also elicit a therapeutic response. Payload - elicits the desired therapeutic response. Linker - attaches the payload to the antibody and should be stable in circulation only releasing the payload at the desired target. Multiple approaches to conjugation have been developed for attachment to the antibody and reviewed. DAR is the drug to antibody ratio and indicates the level of loading of the payload on the ADC.
Activated carbon, in 50% w/w combination with celite, is used as stationary phase in low-pressure chromatographic separation of carbohydrates (mono-, di-, tri-saccharides) using ethanol solutions (5–50%) as mobile phase in analytical or preparative protocols. Activated carbon is useful for extracting the direct oral anticoagulants (DOACs) such as dabigatran, apixaban, rivaroxaban and edoxaban from blood plasma samples. For this purpose it has been made into "minitablets", each containing 5 mg activated carbon for treating 1ml samples of DOAC. Since this activated carbon has no effect on blood clotting factors, heparin or most other anticoagulants this allows a plasma sample to be analyzed for abnormalities otherwise affected by the DOACs. Carbon adsorption has numerous applications in removing pollutants from air or water streams both in the field and in industrial processes such as:
Sources: en.wikipedia.org
When measured by fatalities per person transported, however, buses are the safest form of transportation. The number of air travel fatalities per person are surpassed only by bicycles and motorcycles. This statistic is used by the insurance industry when calculating insurance rates for air travel. For every billion kilometers traveled, trains have a fatality rate that is 12 times higher than that of air travel, and the fatality rate for automobiles is 62 times greater than for air travel. By contrast, for every billion journeys taken, buses are the safest form of transportation; using this measure, air travel is three times more dangerous than car transportation, and almost 30 times more dangerous than travelling by bus. A 2007 study by Popular Mechanics magazine found that passengers sitting at the back of an aeroplane are 40% more likely to survive a crash than those sitting at the front. The article quotes Boeing, the FAA, and a website on aircraft safety, all of which claim that there is no "safest" seat. The study examined 20 crashes, not taking into account the developments in safety after those accidents. However, a flight data recorder is usually mounted in the aircraft's empennage (tail section) where it is more likely to survive a severe crash. Between 1983 and 2000, the survival rate for people in U.S. plane crashes was greater than 95 percent.
The first automated insulin delivery system was known as the Biostator. Currently available AID systems fall into three broad classes based on their capabilities. The first systems released can only halt insulin delivery (predictive low glucose suspend) in response to already low or predicted low glucose. Hybrid Closed Loop systems can modulate delivery both up and down, although users still initiate insulin doses (boluses) for meals and typically "announce" or enter meal information. Fully Closed Loops require no manual insulin delivery actions or announcement for meals. A step forward from threshold suspend systems, predictive low glucose suspend (PLGS) systems use a mathematical model to extrapolate predicted future blood sugar levels based on recent past readings from a CGM. This allows the system to reduce or halt insulin delivery prior to a predicted hypoglycemic event.
AlphaFold has been used to predict structures of proteins of SARS-CoV-2, the causative agent of COVID-19. The structures of these proteins were pending experimental detection in early 2020. Results were reviewed by scientists at the Francis Crick Institute in the United Kingdom before being released to the broader research community. The team also confirmed accurate prediction against the experimentally determined SARS-CoV-2 spike protein that was shared in the Protein Data Bank, an international open-access database, before releasing the computationally determined structures of the under-studied protein molecules. The team acknowledged that although these protein structures might not be the subject of ongoing therapeutical research efforts, they will add to the community's understanding of the SARS-CoV-2 virus. Specifically, AlphaFold 2's prediction of the structure of the ORF3a protein was very similar to the structure determined by researchers at University of California, Berkeley using cryo-electron microscopy. This specific protein is believed to assist the virus in breaking out of the host cell once it replicates. This protein is also believed to play a role in triggering the inflammatory response to the infection.
The enzyme converts adenosine to adenosine monophosphate by transferring a phosphate group. Adenosine diphosphate is produced as a byproduct: The AdK gene/protein is mainly found in eukaryotic organisms and its primary sequence shows a high degree of conservation (>55% aa similarity). However, AdK sequences exhibit low (~ 20-25%), but significant similarity to other PfkB family of proteins such as RK and phosphofructokinases, which are also found in prokaryotic organisms. Although a protein exhibiting AdK activity has been reported in Mycobacterium tuberculosis, sequence and biochemical characteristics of this enzyme reveal it to be an atypical enzyme that is more closely related to ribokinase and fructokinase (35%) than to other ADKs (less than 24%).
Donald has supervised many students and postdocs, many of whom are now professors in reputed universities such as MIT, Carnegie-Mellon University, University of Washington, Seattle, University of Massachusetts Amherst, Dartmouth College, Duke University, Middlebury College and University of Toronto, and researchers at organizations such as NIAID, NIST, IBM, Sandia National Laboratories. Donald is the son of historian David Herbert Donald and historian and editor Aida DiPace Donald. MEMS Protein design NMR Protein Structure Kinodynamic planning Donald is the author of over 100 publications. A representative selection includes:
Sources: en.wikipedia.org
Karl Fischer titration is a common method, using coulometric or volumetric detection. Thermogravimetric analysis can also measure weight loss on heating. Results depend on sample handling because the dried solid can absorb moisture quickly.
The porous cake readily absorbs water vapor from air, which can reduce stability or cause collapse. Vials are sealed with stoppers and crimp seals, sometimes under vacuum or inert gas. Packaging also protects against oxygen and mechanical damage.
Collapse occurs when the product temperature rises above its collapse threshold during primary drying. The ice matrix loses structure, and the cake may shrink or melt back. Formulation excipients and freezing rate influence collapse threshold.
Most lyophilized products are stored in sealed containers at controlled temperature and humidity. Some require refrigeration, while others are stable at room temperature. Protection from light and moisture is often necessary.